Production Speed:

• 1-65 loads per hour
• NOTE: Process rates will vary with load size, number of wraps & conveyor speed

Load Capacity:

• Maximum load weight: 4000# dynamic " 12,000# static
• Maximum load size: 50” W x 60” L (79” max. load diagonal) x 80” H (plus up to 4” top overlap)
• Minimum load size: 30” W x 30” L x 24” H

Rotary Arm:

• 20” diameter ring bearing support system
• ANSI # 60 direct chain drive c/w chain tensioner
• 1-22 RPM rotational speed c/w soft start acceleration
• Final revolution deceleration and positive stop alignment
• 1 HP DC variable speed motor

Film Carriage Elevator:

• 3/4 HP DC variable speed motor
• ANSI # 50 direct chain drive c/w shock dampeners
• Maintenance free 12 point carriage guidance system

Film Delivery System:

• Super Rapid Thread™ 20” capacity pre-stretch carriage
• with Patent Pending pressure balanced nip roller system
• 1/2 HP DC variable speed motor
• Fully electronic dynamic dancer corner compensation
• 33 to 313% fixed stretch capability
• Pre-stretch ratio variable by easy sprocket change
• Rapid Thread™ Safety Door with auto power cut-off switch

Powered Roller Conveyor:

• Basic system: 5ft infeed section, 12ft Process/wrap zone section and 5ft exit section
• Each section includes:
• Chain driven live roller conveyor rated 4,000# per section
• 2-1/2” diameter 11 gauge rollers c/w 11/16” hex axles on 3” centers
• All rollers ANSI # 40 chain driven, roller to roller
• 54” effective roller width
• Conveyor speeds 30 to 60 FPM (specify required speed)
• with electronic soft start
• Pass-line height 18” from floor to top of rollers
• 3/4 HP AC variable speed reversible TEFC motor on infeed & outfeed conveyors / 1 HP AC variable speed
• reversible TEFC motor on process conveyor
• Automatic load indexing and centering by photo-eye & PLC logic

Structural Features:

• All structural steel construction
• Structural tube machine tower & frame
• Electro-static powder coated paint finish

Control Features:

• Allen-Bradley MicroLogix 1400 Programmable Logic
• Controller (PLC) with built-in EtherNet/IP communications
• HMI Touchscreen Operator Interface Panel
• Illuminated Power Start / Reset button
• Emergency Stop button
• Wrap Cycle Start (rewrap) button
• Manual controls provided for rotary arm jog, film carriage elevator lower/raise, film clamp open/close and conveyors forward/reverse
• Wrap Bypass mode selector switch
• Separate film carriage elevator raise & lower speed controls
• Film tension (Force-to-Load) control
• Separate 1 to 12 revolution top & bottom wrap control
• Triple beam auto load height sensing photo-eye, detects dark or shiny loads
• Broken film/out of film detection c/w automatic machine
• reset and fault beacon light
• Rotary arm and film carriage elevator dynamic braking
• NEMA 12 control panel and junction boxes
• Dust tight slip ring assembly
• Non-proprietary UL/CSA approved components

Automation Features:

• Pneumatically actuated film clamp mechanism
• Pneumatically actuated film tail cut/wiper arm
• mechanism
• Ni-chrome impulse hot wire film cut off c/w automatic periodic cleaning cycle

Safety Features:

• Personnel Safety Rotary Arm Obstruction
• Emergency Stop Sensor
• Wire mesh safety barriers enclose the wrap zone to
• prevent personnel intrusion
• Operator Access Gates c/w Safety Interlock Switches
• disable machine operation when gate(s) opened
• Hard-wired emergency stop and operator access gate circuits with Category 3 dual channel safety relays

Electrical Requirement:

• 230 or 460 Volts 3 Phase 60 Hz 30 Amps (required voltage to be specified)
• (other voltages available consult factory)

Pneumatic Requirement:

• 3 CFM @ 80 PSI clean dry pneumatic supply required
• Filter/regulator c/w gauge & lock-out valve provided

Typical System Dimensions:

• 264” (L) x 167” (W) x 140” (H)
• (Overall includes conveyor (L) and Control panel (W) all dimensions approximate)